Vista 10se installation man

The Clock Adjustment prompt is now displayed. This prompt lets you add or subtract up to 59 seconds per day, if needed, to keep the real-time clock accurate. This mode automatically exits after 10 seconds. When activated, three tones will sound at the keypad whenever a door or window is opened.

This feature can only be used when the system is disarmed. Your system may have been programmed to use special keys to manually activate panic functions. The functions that might be programmed are listed below. See your installer for the function s that may have been programmed for your system. Your installer should note the functions that are active in your system. To use a paired key panic function, simply press both keys of the assigned pair at the same time. If your keypad has lettered keys for panic functions, press the designated key and hold down for at least 2 seconds to activate the panic function.

Sends an alarm signal to the alarm monitoring company, but there will be no audible alarms or visual displays. Alarm sends an emergency message to the alarm monitoring company and sounds at keypads, but not at external sounders. Your fire alarm is on 24 hours a day, for continuous protection.

A FIRE message will appear at the keypad and remain on until you silence the alarm. You can silence the alarm at any time by pressing the [OFF] key the user code is not needed to silence fire alarms.

Investigate, and should this be the case, eliminate the source of heat or smoke. If this does not remedy the problem, there may still be smoke in the detector. Clear it by fanning the detector for about 30 seconds. When problem has been corrected, clear the display by entering your [User Code] and pressing the [OFF] key. Should you become aware of a fire emergency before your detectors sense the problem, go to your nearest keypad and manually initiate an alarm by pressing the appropriate panic key s , assigned for FIRE.

The Test key puts your system into test mode, which allows each protection point to be checked for proper operation. Disarm the system and close all protected windows, doors, etc. The keypad will sound a single beep every 40 seconds as a reminder that the system is in TEST mode.

Open and close each protected door and window in turn and listen for the required sounds. The identification of each faulted protection point should appear on the display. Walk in front of any interior motion detectors and listen for the required sound as movement is detected.

The identification of the detector should appear on the display when it is activated. Follow the manufacturers instructions to test the smoke detector, to ensure that all are functioning properly. The identification of each detector should appear on the display. After all protection points have been checked and restored, there should be no zone identification numbers displayed. Determine if the zones displayed are intact and make them so if they are not. If the problem has been corrected, the display can be cleared if you enter the OFF sequence.

User Code and OFF twice. If there are wireless sensors in your system, the CHECK condition may also be caused by some change in the environment that prevents the receiver from hearing a particular sensor. Indicates that a low system battery condition exists, and accompanied by a once per minute beeping at the keypad. Indicates that a low battery condition exists in the wireless transmitter number displayed, and accompanied by a once-per-minute beeping at the keypad.

Either replace the battery yourself or organise service. Some wireless sensors contain a non-replaceable long-life battery which requires replacement of the entire unit at the end of the battery life. The control will not operate while on-line. Wait a few minutes.

The display should disappear. Busy-Standby or DL If this remains displayed for more than 1 minute, system is disabled. Service is required. Long Rng Trbl or bF If programmed, back up long range radio communications has failed.

Service required. Total Power Failure:. At the time of installation, your installer programmed a personal 4-digit master code. As an additional safety feature, temporary user codes can be assigned for use by those not having a need to know the Master code.

NOTE: When performing any of the procedures that follow, do not allow more than 2 seconds to elapse between steps, otherwise the entry will be aborted, and the procedure must be repeated from the start.

The customer must return the equipment to ADT on termination of the contract. FAQs Alarm Memory. Arming The System. NOTE: The security code is always required, however, when disarming the system. Bypassing Protection Zones: Bypassed zones are unprotected and will not cause an alarm if violated while your system is armed. The system will not allow fire zones to be bypassed Using the Bypass key: 6 This key is used when you want to arm your system with one or more zones intentionally unprotected.

Enter the zone number s for the zone s to be bypassed e. Wait for these zones to be displayed, to confirm their bypass. Arm the system as usual. Enter the 2-digit hour setting; enter the 2-digit minute setting. Enter the last two digits of the current year. Enter the 2-digit month setting , enter the 2-digit day setting Press [0] to add seconds per day, or press [1] to subtract seconds per day.

Enter the desired number of seconds per day to add or subtract. Disarming The System. Chime Feature. Function Keys. Types of Panic Alarms: A silent emergency: Sends an alarm signal to the alarm monitoring company, but there will be no audible alarms or visual displays. Contact seller Contact seller.

Visit store Visit store. See other items See other items. Item Information Condition:. The item you've selected was not added to your cart. Add to Watchlist Unwatch. Watch list is full. Last item available. Does not ship to Germany See details. Located in:. Alliance, Ohio, United States. This amount is subject to change until you make payment. For additional information, see the Global Shipping Program terms and conditions - opens in a new window or tab This amount includes applicable customs duties, taxes, brokerage and other fees.

For additional information, see the Global Shipping Program terms and conditions - opens in a new window or tab. Seller does not accept returns See details.

Special financing available. See terms and apply now See terms and apply now for PayPal Credit - opens in a new window or tab. Any international shipping is paid in part to Pitney Bowes Inc. Learn More - opens in a new window or tab International shipping and import charges paid to Pitney Bowes Inc. Learn More - opens in a new window or tab Any international shipping and import charges are paid in part to Pitney Bowes Inc.

Learn More - opens in a new window or tab Any international shipping is paid in part to Pitney Bowes Inc. Learn More - opens in a new window or tab.

Related sponsored items. Showing Slide 1 of 3. New New New. Seller Pre-owned Pre-owned Pre-owned. Last one Last one Last one. Report item - opens in a new window or tab. Seller assumes all responsibility for this listing. Item specifics. Used: An item that has been used previously. The item may have some signs of cosmetic wear, but is Read more about the condition Used: An item that has been used previously.

The item may have some signs of cosmetic wear, but is fully operational and functions as intended. This item may be a floor model or store return that has been used. See all condition definitions opens in a new window or tab.

Custom Bundle:. Alarm Panel. Does Not Apply. Modified Item:. Non-Domestic Product:. Does not apply. The-Security-Outlet wholesale-security-depot Search within store. Visit Store: The-Security-Outlet. Items On Sale. DSC Brand.